Surface Preparation Equipment Repair for Every Major Machine Class
Legacy Industrial Solutions does deep repair on every major class of surface preparation machine. Nothing starts until you have seen the diagnosis and approved the estimate, so a repair stays a repair unless you decide otherwise. The five classes we service are below.
One shop, every major machine class
What We Repair, Class by Class
Every machine category we advertise gets the same depth: a clear scope of repair, the failure themes we see most, and a link to the dedicated page for that class.
Concrete Floor Grinders & Polishers
We repair vibration and driveline wear, hub and spindle bearings, belt tension, motors and gearboxes, electrical and switchgear, propane fuel systems, and water-fed or dry setups.
GRINDER REPAIR DETAILSShot Blasters
We service blast wheels, blades, liners, control cages, impellers, seals and magnets, shot recovery and separation, and dust seal integrity for floor-preparation shot blasters.
SHOT BLASTER REPAIR DETAILSFloor Scrapers
We handle hydraulic and drive faults, blade and blade-holder wear, cylinders, hoses, pump and valve service, linkage and tracking on walk-behind and ride-on scrapers.
FLOOR SCRAPER REPAIR DETAILSScarifiers / Planers / Milling Machines
We service cutter assemblies and drums, bearings, belts and tension calibration, depth and angle setup, and drivetrain repairs that keep profiling consistent.
SCARIFIER REPAIR DETAILSDust Collectors & Vacuums
We repair HEPA and sock filters, airflow and suction loss, motor amperage and carbon brushes, hoses and fittings, electrical panels, and leak tracing on industrial extractors.
DUST COLLECTOR REPAIR DETAILSSteel Surface Finishing Machines
The same shop repairs the shot blasters and grinders used to blast, grind and polish steel plate, reservoir and tank liners, and steel decks. Steel punishes the machine differently: finer dust, harder plate, and a finish the customer can see.
Trusted brands we service
Husqvarna, Blastrac, SASE, Bartell, Terrco, STI, CPS, National Flooring Equipment, and BlastPro. Legacy Industrial Solutions is an independent repair shop. If your make is not here, call us.










We Show You the Work Before We Do It
Most repair providers in this market are equipment sellers first and repair shops second. That creates a tension every customer should see: the same counter that can fix your grinder can also sell you a new one. When a rebuild turns into a replacement conversation, the customer keeps control only when the diagnosis comes first and the estimate is approved before work starts.
Nick has experience finishing floors and training machine operators, and he can travel to worksites to demonstrate machine use. We do sell machines, which means we cannot claim the absence of the sales incentive. What we can do is make every recommendation inspectable: you see the diagnosis, you approve the estimate, and if we think replacement makes more sense than a rebuild, we tell you why before we tell you what we would source.
From Intake to Return: A Clear Process
We keep the process simple so the machine gets to the right bench quickly and you stay informed at every stage.
Intake
Call or submit a service request. Tell us the make, model, serial number if you have it, symptom, and whether you will drop off or ship.
Diagnosis
We inspect the machine on the bench, trace the fault, and identify what parts or rework are needed to bring it back to spec.
Estimate
You receive a written estimate with the scope, parts, and labor before any work begins. No surprise invoices.
Repair & Test
Approved work is performed on the Santa Fe Springs bench, then tested under load to confirm the fault is resolved.
Return
Local pickup or coordinated freight back to your shop or jobsite. We help crate or palletize when needed.
Warranty
Every repair is backed by a 90-day workmanship warranty. Parts carry the applicable manufacturer warranty.
Scope of Service
- Depot repair: performed at our Santa Fe Springs shop.
- Nationwide freight: machines ship in and out from anywhere in the country.
- Field service: available depending on scope and location.
Communication Promise
We can't promise a fixed turnaround, because machine condition and parts availability are unpredictable. Instead, we promise fast diagnosis, a fast estimate, and clear updates at every stage so you are never guessing about your machine.
READ THE FULL PROCESSTechnical Services Behind the Repair
Surface preparation machines fail across mechanical, electrical, fuel, and hydraulic systems at the same time. We keep the capability in-house so one shop can handle the full machine.
Not Limited to Southern California
We are one shop in Santa Fe Springs with a freight lane in both directions. Contractors outside SoCal ship palletized heads, motors, and full machines to our dock; we repair and coordinate the return shipment. The depot model turns a single location into national coverage without inventing a physical footprint we do not have.
SHIP A MACHINE FOR REPAIRReady When Your Machine Is Down
Call the Santa Fe Springs bench now, or submit a service request and we will respond the same day. Whether you are local or shipping from across the country, the next step starts with a conversation.